How to Replace a Tub
How to Replace a Tub
Blog Article
Are you currently interested in information and facts about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably tough job. If the old tub is conveniently easily accessible, the task can relocate quickly; if you need to open up a wall to get rid of the old tub and place the new bath tub, the job is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the brand-new one. Make sure you have actually qualified on your own for the job as well as are comfortable trying it. Rather than working with a professional to take control of a halfway-completed job, it is better to think about employing one prior to you start. Opportunities are you may require a professional plumber to make tube connections.
This article will aid you set up a brand-new bath tub in your restroom if you have actually currently bought a brand-new bathtub and don't require to transform the arrangement of your previous water system pipelines.
Your devices and also material list should make up the following:
Preparing for the Installation
To start with, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets device to prevent stress on the tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any water remaining in the system. The process of removing the existing taps can be quite problematic as a result of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the staying water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Using both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub until the level checks out level.
To mount taps, fit all-time low of the furthest flexible faucet connector to the ideal supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the supply of water and also inspect all joints and brand-new pipework for leaks as well as tighten them if required. Load the bathtub as well as likewise examine the overflow outlet and also the typical outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has actually been used a minimum of once as this will resolve it into its last position.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washing machines are in location in between the faucet and the sink. Protect the faucet in place with the producer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to split an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to permit the activity experienced when the bathtub remains in usage. The sealer can split relatively very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that page about How to Install a Bathtub Yourself while browsing on the web. Sharing is nice. You just don't know, you may just be doing someone a favor. We treasure reading our article about Tools You Need to Install a New Bathtub .
Click Here To Read More Report this page