Just How To Install A Bathtub (For Newbies).
Just How To Install A Bathtub (For Newbies).
Blog Article
They are making a few good pointers relating to How to Install a Bathtub overall in this post just below.
Installing a bathtub isn't precisely brain surgery, yet it does need strong plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably difficult project. If the old tub is easily available, the project can move rapidly; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the brand-new one. Make certain you have actually certified on your own for the work and are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to consider using one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your shower room if you have actually currently gotten a new tub as well as don't need to alter the plan of your previous supply of water pipes.
Your tools as well as material checklist ought to comprise the following:
Planning for the Setup
First of all, the sustaining frame supplied with the bath needs to be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Using both wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are practical in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the level reviews level.
To set up faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water supply and inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has actually been made use of at the very least once as this will settle it into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. As soon as the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The former type needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to crack a rigid seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, leading to complications with wetness and also feasible leakages to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can fracture relatively early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently readily available on the market. It is recommended to fit the floor tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed our part on Installing A Bathtub. Many thanks for taking the time to browse our short article. Loved our entry? Please share it. Help somebody else check it out. I truly appreciate reading our article about How to Install a Bathtub Yourself.
Rates Report this page